I am using a NXP (freescale) 33883 H-Bridge gate driver IC to drive a simple H4 bridge circuit which is connected identically to that in the application schematic in the datasheet: I am switching at 25kHz using bipolar modulation and maintaining a duty cycle of 50 as it is being switched over a transformer.

If I use a H-Bridge, the 12V should be enough, so I don't need a transformer. The current would be about 40mA (20mA - 100mA). I can make a short-safe H-bridge for 0.1V - 11.9V output, but I would need 8 transistors (BC547/BC557) per H-Bridge. So I hope there is an easier way. The Si9986 is an integrated, buffered H-bridge with TTL compatible inputs and the capability of delivering a continuous 1.0 A at V DD = 12 V (room temperature) at switching rates up to 200 kHz. Internal logic prevents the upper and lower outputs of either half-bridge from being turned on simultaneously. Note also that you can't build a simple "all N-Channel MOSFET" h-bridge (unlike this hybrid design) without a proper "high-side driver" design; such a design can be built from discrete components, but usually it's better to just use an off-the-shelf high-side driver IC (or a half-bridge driver IC to control both MOSFETs on a side). † VCM Driver † Brushed Motor Driver † Stepper Motor Driver † Power Converter † Optical Disk Drives † Power Supplies † High Performance Servo DESCRIPTION The Si9986 is an integrated, buffered H-bridge with TTL compatible inputs and the capability of delivering a continuous 1.0 A at VDD = 12 V (room temperature) at switching rates A robust lateral power MOSFET buffered H-bridge motor driver power IC Figure-5 illustrates the drain voltage and the source current of the non-isolated n - channel MOSFET used in the H - bridge driving an inductive load of IniH with 1R series resistance. The UVLO circuit prevents turn-on of the MOSFET or IGBT until there is sufficient VBS or VCC supply voltage. The IX2120 is available in a 28-pin SOIC package. IX21844: High Voltage Half-Bridge Gate Driver: Floating Channel for Bootstrap Operation to +600V with an Absolute Maximum Rating of +700V; Programmable Dead-Time

Jul 31, 2018 · Revisions on m H-Bridge addressing use input. See link page is being updated. http://www.bristolwatch.com/ele/h_bridge.htm

Dec 08, 2007 · HI, I need to build a 2 H-bridge driver with 4 N-MOSFET to drive a PMDC motor. The motor have rated voltage 24V and rated current 8.5A. So, I choose the IRFP 260 N-MOSFET because it can sustain the current untill 45A in order to protect the MOSFET from over current. But the problems I face high-side driver and an inverting low-side driver. The MAX15012A/B/C/D feature CMOS (VDD/2) logic inputs. The MAX15013A/B/C/D feature TTL logic inputs. The drivers are available in the industry-standard 8-pin SO footprint and pin configuration and a thermally enhanced 8-pin SO package. All devices operate over MOSFETs: MOSFET Master Table; N Channel: N Channel 30V; MOSFETs - Automotive; N Channel: N Channel 8V to 29V; N Channel: N Channel 31V - 99V; N Channel: N Channel 100V - 399V; Complementary Pair (N+P): 30V Complementary; Complementary Pair (N+P): 31V to 100V Complementary; Complementary Pair (N+P): 8V to 29V Complementary; P Channel: P Channel 30V Integrated Circuits (ICs) – PMIC - Full, Half-Bridge Drivers are in stock at DigiKey. Order Now! Integrated Circuits (ICs) ship same day

An H-Bridge is used to control the direction of the motor and to also provide enough current for the motor to run. Operation: 1. To force a motor to switch in two directions, one requires a minimum of 4 switching elements. We will use 4 MOSFET to control the direction of the motor. Consider Figure 2 shown below. Figure 1: H-Bridge Configuration

high-side driver and an inverting low-side driver. The MAX5064A/B offer two inputs per driver that can be either inverting or noninverting. The MAX5062A/B/C/D and the MAX5064A feature CMOS (VDD / 2) logic inputs. The MAX5063A/B/C/D and the MAX5064B feature TTL logic inputs. The MAX5064A/B include a break-before- STDRIVE MOSFET and IGBT gate drivers can integrate a comparator for protection, an operational amplifier for current sensing and an integrated bootstrap diode, thus reducing the number of external components required at system level. An h bridge is a circuit that is used primarily to control motors; they allow for forward and reverse motion of the motors. Therefore, the motor can be utilized with its full bidirectional capability. To build an H-bridge, the only option is not to use an IC chip for an H-bridge.